iPhone mount (again)

Finally pulled my finger out and sorted my iPhone mount on my bike. I went about a week before pulling it off again and attempting to get a charger in to the waterproof case ("iDry" from Amazon/eBay) as well.

Modified iDry case on BMW GSA.

On-bike view. I use Tom-Tom and MotionX GPS apps.

Protected from the worst of the elements by the screen.

The same mount as before - can be vertical or horizontal.

Cheapo charger bought mainly for cable and connector.

I cut a slot in the inside wall (double wall at bottom) with my Dremel clone. I dismantled the connector and moved the PCB on to short flying leads to allow me to glue the connector in the slot I just made. The PCB sits at a right-angle in the small cavity were the hinge pin sits. Cable entry strain relief, PCB and iPhone connector are all fixed and sealed with hot-melt glue. The particular glue I have remains rubbery and allows the connector to move slightly as I fit or remove my iPhone.

Original cable grommet was used, but it was cheap and split almost immediately.

Standard car power socket spliced into aux power socket (for flexibility).

I spliced a cable mount accessory socket (which I already had in my collection of crap) on to the bike's power socket, which stays on for 5 minutes after key-off. I could have hard-wired it but this gives me more options.

The original iPhone charger I used was one of two (one in the car) cheapo chargers from Amazon. It stopped charging after a couple of rides. Testing showed the DC-DC converter inside didn't seem to always start up correctly. Through this, I found that the iPhone 3G is 12V tolerant - it is protected against having 12-odd volts connected to it's power pins!

I bought another generic phone charger (I already had the connector) from Tesco late one evening. It was rated at 5V 500mA, great, that should do it. After another couple of rides it too was dead. Further testing (which I should have done to begin with) showed that with Sat-Nav running and playing music over Bluetooth; the iPhone 3G was pulling up to 800mA. No wonder the cheap chargers aren't up to it.

I was looking through my parts looking for a LM7805 or similar, I was going to make up a small board. I then came across a small Traco DC-DC converter which I'd forgotten I had. Checking the datasheet; it has a wide input voltage range and adjustable output voltage and current up to 2A! It even has a enable line. Perfect.

I added some caps, as per the datasheet and re-used one of the cheapo housings to keep it together. Plenty of "anti-vibration" hot-melt to keep it from falling apart and the job's a good 'un.

Phone now charges from flat even if in heavy use. I'm a happy chappy.

The bike rocks, BTW. ;-)

New bike, new possibilities

I've got myself a BMW R1200GS Adventure! I'm due to pick it up on Wednesday and can't wait!

I've already got a project in mind for it; a little electronics add-on...

And I'll have space for my iPhone/SatNav now too :-)

An awesome piece of engineering.

Unforeseen situation

Well, it stayed on; didn't work lose and was bone dry inside even after heavy rain. What I hadn't accounted for was the screen randomly spinning; upside-down, side-ways and back again. The Tom Tom app has no screen lock and because my bike has such a small cockpit; there's only one place it can go and it sits at a shallow angle where vibration and bike movement confuse the hell out of the accelerometer. It's useable, but annoying.

Perhaps more damping, somehow. Or a steeper angle (making it harder to see, though).

Ideas welcome.

iPhone mount: final assembly (no power yet)

Reassembled, it doesn't look too bad (IMO), good enough to serve the purpose. I'll test it on the way to work tomorrow, probably with the supplied lanyard tied to the bars (just in case). I didn't put any top-coat on, so let's see how the paint holds up.

iPhone mount: paint and assemble

I've been hanging on to a heavy-duty plastic bracket for about three years now. I think it originally came off a car phone mount; a piece of someone else's junk saved from the skip. Now it seems almost perfect for modding into a handlebar mount, with the addition of some stainless steel M4 screws and a small rectangle of 6mm polycarbonate. Thin sheet rubber (again, saved off-cuts) serves to provide grip and some vibration cushioning.

Old phone bracket serving as bar clamp, screwed into iDry base.

Only a single stainless steel M5 holds the iDry case in place. Will it be enough?

The above photos show the disassembled iDry case; the top comes off simply by pushing out the hinge-pin, and the end locking handle comes off with two small screws.

Some more thin rubber sheet, laid inside, should help prevent scratching and provide a little more cushioning.

Thin rubber sheet and double-sided sticky tape ("for quickness").

Rubber sheet added to bottom and back.

With that done, I needed to spray the in-your-face white. I had white, fluorescent orange or gloss black...

Sprayed gloss black (looks like grey in pic).

Safety lock removed before spraying.

Left to dry briefly before each light coat, then left to dry properly.

iPhone on motorcycle?

I recently bought the Tom-Tom app for my iPhone; it's my first Sat-Nav and worked quite well stuffed inside my jacket pocket, giving turn-by-turn prompts to me over Bluetooth in my helmet. Less than ideal satellite visibility and not being able to see the additional info on the screen, prompted me to mount it on the bike.

My motorbike doesn't have a lot of cockpit space; no fairing or screen and not much room on the bars, so I didn't think the commercial (and expensive) bike mounts would be suitable. Most mounts I found only held the iPhone and offered no impact resistance or weather protection.

So I looked for a hack-together solution. I ordered an iDry waterproof iPhone case from Amazon, with the intention of making holes in it! I need a secure mounting and ideally be able to charge the phone while on the bike.

iDry waterproof case

It's not clear from the photo or the description that the screen cover is a silicon rubber, fine if it's wet, but difficult to pinch-zoom when it's dry. Not that I'm bothered; it'll be difficult enough with gloves on (more on that another time). I don't like the white either, but it doesn't come in any other colour, so I may have to paint it.

I'm not planning on submerging it, so if I'm careful, any holes I make shouldn't be a problem. Although it's also not clear, from either photo or description, if there was any kind of access port for the connector. There isn't. I'm not entirely sure how I'm going to get power into the box in a robust, weatherproof way. Let's get it mounted first, but I have to take account of the opening mechanism:

Operation